Get Those Pipes Fixed With These Plumbing Tips

Posted By on June 4, 2014

Get Those Pipes Fixed With These Plumbing Tips

You need to have some knowledge of what to look for and expect from doing your own plumbing. You need to know what resources are available to you and who can provide you answers as to what you need for your future plumbing jobs. The tips below can help you with how to start.

Do not try to sell a product that you do not agree with. This includes paying attention to the company itself and their values and policies. If you have any qualms about the company, your customers will pick up on it. You want to be a full supporter of the product you are selling

Solder with safety in mind. When you solder a copper pipe you want to direct the flame on the copper pipe. The flame of the torch has to be four inches away from the piping. The flame should be targeted directly at the point where the copper piping needs to be disconnected.

Roots from a tree in your back yard can be a real headache when it comes to plumbing. Make sure if you have a big tree or bush or some kind of plant with a big root system, that you ask your plumbing company about root killing agents. You can flush these down your toilet and kill any roots that may be blocking your pipes and save yourself a lot of money by stopping a back up before it happens.

Look closely at your toilets several times throughout the year. Check to see if there are any leaks that you may not have noticed; you can do this by placing five or six drops of food coloring in the tank. If there is a leak, the color will seep into the bowl within half an hour. This process will help you catch a small problem before it gets too out of control.

Be careful about using liquid clog cleaners. These liquids can contain chemicals that are extremely bad for your pipes. Instead, use a snake or a plunger to dislodge any clogs you might encounter. Be sure to try these things before giving up and calling a plumber, who will probably re-perform those same acts.

Make sure you clean out overflow holes in your kitchen and bathroom sinks on a regular basis. These holes are intended to act as an emergency fail-safe to prevent spillage from a full sink, but if they are clogged they can’t do their job. You can clean out an overflow hole using the same techniques you would for a clogged drain.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Set the temperature on your hot water heater to a temperature that does not exceed 120 degrees. This helps to save energy and prevents the water from becoming too hot and potentially scalding someone in your household. Older models that do not have a temperature setting should be set on Medium.

Don’t shrug off that trickle coming from your toilet as a small problem. Even the tiniest leak can be quite expensive in the long run as you end up wasting potentially hundreds of gallons of water. See if you can find the root of the leak, or seek out professional advice, and keep your toilet running efficiently.

Believe it or not, it is not a very good idea to use a plunger if your toilet is clogged. Plungers just push whatever is stuck deeper into the drain. Instead, it is a better idea to use a closet auger. It will do a better job and is affordable.

Check your toilet regularly for leaks. An easy way to check for this is to drop some food coloring in the toilet tank. If the water in the bowl turns colors, it is leaking.

When you’re going away on a vacation, you should consider shutting off the water supply to your home. This can help stop many problems before they start. If you don’t do this, you should have someone stop by your house regularly to check that nothing has gone wrong and that your home isn’t flooded.

In the winter months, if you live somewhere where temperatures fall below freezing, leave your faucets on a little bit to let a thin stream of water through. This will help prevent the pipes from freezing, which could be a major problem for you and all the pipes in your home.

The most important plumbing tip you need to know is — how to turn off your home’s main water supply. Once the water is shut off, you can investigate problems and figure out how to resolve them. Walk the family through the house and show them where all the water shut-off valves are, and how to use them.

As you have seen in the above tips, there is a lot of knowledge you can acquire before starting to do your own plumbing and it’s this knowledge that can help you with your future plumbing jobs. Do everything you must to find out what you need to get started.

About the author

Comments

Leave a Reply